Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
What are your opinions on How to Install a Bathtub Yourself?

Installing a bathtub isn't exactly rocket science, but it does call for solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a moderately hard task. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you have to open a wall surface to remove the old bathtub as well as position the new tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. See to it you have qualified on your own for the task and fit trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to think about employing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your restroom if you have currently acquired a new tub as well as don't require to transform the arrangement of your previous water pipelines.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipes. When the supply pipes have been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former kind ought to be linked to the tap finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the tub till the level reviews degree.
To install taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub must wait till the bathtub has been made use of at least once as this will resolve it right into its final setting.
Getting ready for the Installment
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about issues with wetness as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and cartridges, and are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I was shown that article about Tools You Need to Install a New Bathtub from an acquaintance on another blog. Do you know another person who is curious about the subject? Take a moment to share it. We love reading our article about Installing A Bathtub.
Click Here To Find Out More
Report this page